qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 1 of 7 version# 1.0 feature: ? water transparent ? package in bulk and tape and reel ? high radiant intensity ? peak wavelength 85 0nm ? al gaas technology ? 30 deg emitting angle description: this device is spectrally match with phototransistor, photodiode, and infrared receiver module application: ? infrared illumination ? telecommunication system ? infrared applied system ? sensor application certification & compliance: ? ts16949 ? iso9001 ? rohs compliant dimension: units : mm / tolerance = +/ - 0.1mm
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 2 of 7 version# 1.0 elec trical / optical characteristic (t=25 o c ) product i f (ma) v f (v) p (nm) e (mw/sr) typ. max . min. t yp. max. min . typ. qbed 9345 50 1 .5 2.2 82 0 85 0 88 0 37.2 10 0 absolute maximum rating material p d (mw) i f (ma) i fp (ma)* v r (v) t op ( o c) t st ( o c) t sol ( o c )** al gaas 150 70 100 5 - 40 ~ + 80 - 40 ~ + 100 260 *duty 1/10 @ 1 0 khz ** ir r eflow for no more than 10 sec @ 260 o c
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 3 of 7 version# 1.0 characteristic curves: al gaas material
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 4 of 7 version# 1.0 solder profile & footprint: a. soldering 1. when soldering, the soldering iron needs to be at least 2mm away from the epoxy edge. after soldering, allow at least 3 minutes for leds to cool back to normal temperature. do not apply any pressure to the epoxy encapsulation or the lead frame d uring the soldering process. 2. when reflow soldering or wave soldering, please solder once for less than 5 seconds at a maximum temperature of 260 c. during the soldering process, if the temperature or timing is not controlled within limits, it would cause t he epoxy to deform or cause the die or wires within the led to be damaged. 3. when using soldering iron, please solder once for less than 5 seconds at a maximum temperature of 300 c. when soldering a row of led on a pcb, please do no t solder both leads of a led in sequence. (solder all the positive lead first, then all the negative wave soldering profile for lead free process:
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 5 of 7 version# 1.0 leads) 4. do not dip the epoxy encapsulation part of led into any soldering paste liquid. 5. after soldering, do not adjust the location of the led anymore. when attaching electronic parts to a pcb with leds, the curing time for the whole pcb should be less than 60 seconds, at less than a temperature of 120
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 6 of 7 version# 1.0 label ing : ordering information: part # orderable part # spec range quantity per reel qbed 9330 qb ed9 3 30 ie = 100 mw/sr @ 50ma, p = 85 0nm tbd
qbed 9330 5mm ir emitter product: qbed 9330 date: 06/25/2011 page 7 of 7 version# 1.0 revision history: description: revision # revision date new release of q bed9 3 30 v1.0 06/25 /2011
|
